Future & Energies

Composants électroniques et developement de projets

Composants imprimante 3D

Composants mécaniques: structure

kit 1 imprimante 3D 

Le kit comprends:

-1 Arduino mega 2560 R3

-1 cable USB

-1 X Ramps 1.4

-5 X A4988 module

-5 X Heat sink

Kit 2 imprimante 3D

Le kit comprends:

-1 Arduino mega 2560 R3

-1 écran LCD 12864 ramps

-1 cable USB

-1 X Ramps 1.4

-1*RAMPS1.4 LCD 12864 LCD

-2 cables de connection

Kit 3 imprimante 3D

Le kit électronique comprends:

-1 Arduino mega 2560 R3

-1 écran LCD 12864 ramps

-1  Ramps 1.4

-1 cable USB

-5 DRV A4988

-5 heat sink 

-2 cables de connection

Rocker power switch 10A 250V

Prise D'alimentation avec Interrupteur Fusible
Taille totale: 5x3x3.2 cm/2 '' x 1.2 '' x 1.3 '' (L*W*H)
Type De prise: 3 Broches IEC320 C14

Cliquez ici pour modifier le texte

Limit end switch

3D Printer Mechanical Limit

Ramps 1.6 pour arduino Mega 

-Printer Control Reprap Mendel   Prusa 


-Dimensions : 101.5 * 60.5mm

3D Printer Parts MKS Gen V1.4 Control Board with MKS TFT V2.0 Smart Touch Screen .

Le kit comprends:

1-MKS Gen V1.4  Board        

1-MKS TFT V2.0      

The board features a developer friendly expansion port supporting giving access the same as Ramps1.4.
MKS Gen is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
MKS Gen retains all interface of ramps1.4.             

Ecran touch 3.2  MKS TFT 2.0

Easy DISPLAY + SD-CARD connector, RepRapDiscount SmartController compatible pin header on board

Easy connect MKS TFT on AUX-1
All extra pins broken out the same as ramps1.4(AUX-1,AUX-2,AUX-3,Servos1)

3D Printer Heated Bed Power Module  MOSFET High Current Upgrade RAMPS 1.4 / 1.5.

This module under the premise of
normal cooling, found at  I (Max) = 25A stable work situation,
  Max courant :25A

Extrudeur Titan direct drive

Reprap kossel MK8 J-head

1,75mm / 3mm filament 

Nema 17

Ventilateur 12V  30mm x 30mm

Ventilateur 12V

Heater aluminium block MK7/MK8

  • Material: Aluminum 
  • Dimensions: 20 * 20 * 10mm
  • Heater Mounting Hole: 6mm diameter
  • Screw hole: M3
  • Thermocouple mounting holes: M3

Ecran LCD 12864

-3D printer RAMPS1.4 LCD12864 intelligent smart 

-1 L adapter plate .

-2 câbles plat.

Ecran LCD 2004

- 3D printer reprap smart controller Reprap Ramps 1.4 2004 LCD control.

-1 L adapter plate 

-2 cable  plat.

 Stepper motor driver A4988

- 5  driver A4988  avec heat sink 

- Power triode

 -3,50$ l'unité

Module L298N H bridge
Dual H Bridge DC Stepper Motor Drive Controller Board Module .

  • Working mode: H bridge 

   Kit  CNC Shield V3 3D printer

CNC shield v3 engraving machine  pour Arduino UNO / 3D Printer / + 4  A4988

le kit comprends:

-1 X cnc shield v3

-4 X DRV8825

-4 X Heatsink en aluminium

Arduino Mega 2560 R3.

Microcontroller ATmega2560
  -Operating Voltage 5V
  -Input Voltage  7-12V
  -Input Voltage (limits) 6-20V
  -Digital I/O Pins 54 (of which 14 provide  PWM output)
  -Analog Input Pins 16
  -DC Current per I/O Pin 40 mA
 - DC Current for 3.3V Pin 50 mA
  -Flash Memory 256 KB of which
      4 KB used by bootloader

3D Printer Parts Reprap Makerbot MK8 .


3D Printer Parts Reprap 

Remote Bowden Extruder pour filament 1.75MM 

Rouleau de filament pour 3D .

- ABS   Dia. 1,75mm
- PLA    Dia 1,75mm
-PETG Dia. 1,75mm
- Poids  :1Kg

Gamme importante de couleur


 Stepper Motor driver TMC2130

-Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axe

Built-in Driver Current 1.4A Peak Current 2.5A
Driver capabitlity up tp 1.2A(RMS) continus coil current
Step/dir interface with up to 256 microsteps
SPI interface or CFG pins for configuration
Motor voltage: 5.5-45V
Logic voltage: 3.3-5V
Stealthchop- for quite operation and smooth motion
spreadCycle-highly dynamic motor control chopper
coolStep-current contril for engergy savings
stallGuard-sensorless motor load detection
dcStep-load dependent speed control

Stepper motor nema 17

(Imprimante 3D)

17HS4401S , 1,7A

Step angle: 1,8 deg.

Motor lenght : 40mm

Holding torque: 45N.cm

Detent torque : 2,65N,cm

Rotor inertia: 65 g.cm2

Lead wire  : 4

Extruder Micromake J-head


 -Extrudeur plus précis en control de température  
 -Plus de surface de contact  la résistance le thermistor et le bloc d'aluminium
-Buse 0,4mm

3D touch auto leveling sensor.

Compatible FDM 3d printer

-TL-touch is an auto leveling sensor for 3D Printers based on open-source. 

-Simple, Smart, High-precision,It could work with any kinds of bed materials, such as glasses, woods, metals, and so on.

 Support  steering engine , Marlin ,Repetier ,Smoothieware,etc.

Alimentation 24V 10A

Courant de sortie: 0 ~ 10A

Poids Net: 500 grammes

Dimension: 165*99*39mm

Conformité de sécurité: CCC/Rohs

haute prix-efficace, fiabilité avec les normes de l'industrie

Température de fonctionnement: 0 ~ 40C
Humidité ambiante: 0 ~ 95% Non-Condensation

Tension d'entrée: AC110V/220 V 

Alimentation 12V 20A

Puissance: 240 W

Tension d'entrée: AC110V/220 V

Tension de sortie: DC 12 V

Courant de sortie: 0 ~ 20A

Poids Net: 500 grammes

Dimension: 165*99*39mm

Conformité de sécurité: CCC/Rohs

haute prix-efficace, fiabilité avec les normes de l'industrie

intégré dans plus de tension, plus de courant, et court-circuit protection

Alimentation 24V 20A 480W

Input Voltage:  AC110V/220V

Output Voltage: DC 24V

Output Current: 0~20A

Net Weight:  900gram

Demension: 215*115*50mm

Shell Material: Metal case / Aluminum case

Safety Compliance: CCC / Rohs

Built-in over voltage, over current, and short circuit protection

Working Temperature: 0~40C
Storage Temperature: -20~60C

Courant de sortie: 0 ~ 20A

3D printer extruder mk8 Ultimaker 12V 0,4mm single nozzle print with a fan and thermistor.

-Flow :support 100mm/higt speed printing

-Mvt shaft speed :0,1-40mm /s

-Normal operating temp: 170-250 deg.

-Extuder nozzle: 0,4mm

-Print material : ABS ,PLA 

E3D V6 end full kit 1,75mm 12V
Bowden /Reprap 3D printer 

1 x Stainless Steel Heatbreak
1 x Brass Nozzle (0.4mm)
1 x Aluminium Heater Block
1 x 100K NTC 3950B
1 x Heater Cartridge (12v/24V)
1 x 30x30x10mm fan (12v/24V)
1 x Thermistor high temperature line

Thermistors 100K ohm NTC 3950

Cliquez ici pour modifier le texte

Switch optique


Pour imprimante 3D

Melzi  2.0 Control board 

- Reprap melzi 2.0 1284 P

- Tension de fonctionnement: 12 V

- IC: atmega1284p

3. FT232RL USB interface 

4. 4 pcs A4988 Stepper Motor pilote 

5. Peut contrôler: Mk1, Mk2A, MK2B, MK3 

6. Taille: 210mm * 50mm * 17mm 

Buse pour imprimante 3D

Diametre de 0,2mm , 0,3mm , 0,4mm , 0,6mm , 0,8mm ,1,00mm   (brasse)

- Pour filament 1,75mm 

MKS Gen V1.4 control board Mega 2560 R3 motherboard (compatible ramps1,4)

Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.

Replace the motor drive, drive and support 4988 8825 drive.
Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.

MKS base 1.4 control board compatible ramps1,4.

MKS Base V1.5 is the latest version,it is the combination of Arduino MEGA2560  plus RAMPS1.4 and A4982 in 3D printer. It is a feature rich all-in-one  electronics solution for Reprap and other CNC devices. It features an  onboard ATmega2560. Its five motor outputs are powered by A4982 stepper  drivers. It use FTDI FT232R device for USB and not ATMEGA16U2 as ARDUINO  MEGA2560. The board can use the same firmware as Ramps1.4. MKS Base V1.5  is designed to be flexible in the user's power source availability,  allowing any power supply from 12V-24V. It is supplied with a Marlin  firmware. 

Timing belt GT3

Pour CNC  machine ,...


Belt Height:2.41mm

Tooth Height:1.14mm


Material:Rubber With Fiberglass Core

Filament pour imprimante 3D 

Diam: 1,75mm

Poids : 1Kg 

Flexible shaft coupling
- 5mm x 8mm    ou
- 6,35mm X 8mm

Long : 25mm

Mat : Aluminium

Stepper motor Driver DRV8825

-CAN interface directly with 3.3 V and 5 V systems .

- Maximum 45 V supply voltage

- built-in voltage regulator

- Up to 2.2 A per coil with sufficient additional cooling

Flexible shaft coupling 

-Dia.: 8 X 8mm 

-Long.: 25mm

-Mat.: aluminium

Poulie dentée  GT 2 16 dents

-Mat .: Aluminium

-Dia.: 5mm bore

Pour courroie dentée  GT2 de 6mm de large

Roulement a bille 608ZZ 
-Dim.: 8 X 22 X 7mm
-Precision ABEC-5

-1 rangée de bille 

Roulement 688ZZ

ABEC -5 
-Dim.: 8 x16 x 5mm

Roulement 623ZZ

Dim.: 3 x 10 x 4mm

Shaft 10mm long: 500mm

Stainless steel

Engrenage MK8 5mm

Pour filament 1,75mm

Poulie 32 dents GT2

- 5mm  bore  (nema 17)      ou

- 6,35mm bore (nema 23)  ou

- 8mm bore

Poulie 20 dents GT2

-5 mm bore (nema17)

Poulie GT2 20 dents bore 5mm

-Timing poulie d'entraînement GT2  en aluminium avec roulements.

Poulie GT2 20 dents bore 6mm

-Timing poulie d'entrainement en aluminium avec roulements

Poulie GT3 20 dents

- 6,35mm bore pour CNC

Timing belt GT2  6mm 

-Longueur 10M

-Mouvement linéaire et positionnement

-Pour Poulie GT2

Stepper motor nema 17

Model: 1703HS168A

Step angle: 1.8 deg

Motor lenght: 40,0mm

Rated current: 1,68A

Holding torque: 62,0 (oz/in)

Holding torque : 4,4 Kg.cm

Rotor inertia:54 g.cm2

Stepper motor nema 23  56mm

Model: 2303HS280AW

Motor lenght:56mm

Step angle: 1.8 deg

Current/phase: 2.8A

Holding torque: 175,0 oz/in.

Holding torque: 12,6 kg.cm

Rotor inertia:300g.cm2

Model number : XB20*25-6.35*8

Long: 25mm

Dia.: 20mm

Type : BFseries

Materiel: polyurethane

       Support SK8  8 mm


-Pour CNC , imprimante 3D , CNC .

-Support pour rod diam. 8mm

Heated Bed Power Expansion Module High Power.

Heated bed power module
Based on powerful MOSFET HA210NO6
Size: 60*50mm
Mounting holes: 3.2mm diameter, for M3 screws.
Distance betweeen holes: 54*43mm
Very powerful MOSFET to withstand higher current than normal RAMPS or other 3D Printer controller can handle
Voltage: 12V-24V

Senseur de détection de proximité

 -Modèle: LJ12A3-4-Z / PAR
-Tension de fonctionnement: DC 6-36V 
-Type de sortie: PNP trois lignes normalement ouvert
-objet de détection: objets en métal
-Distance de détection: 4 mm
-Courant de sortie: 300 mA

-Inductifs Détection Sensor Switch PNP DC6-36V

Inductifs Détection Sensor Switch PNP DC6-36V

Extruder E3D-V6 volcano

  • 1 * E3D V6 HeatBreak
  •     1 * HeatSink
  •     1*Heater Block
  •     1* Volcano Nozzle 0.8mm
  •     1 * 12 V, 40 W heater cartridge
  •  1 * Semitec 104GT-2 thermistor

Ventilateur Dc12V 40 x 40mm

Ventilateur pour imprimante 3D

Heatbed 200 x 200mm x 3mm MK3

-Épaisseur 3mm 

-En aluminum 

-Dual power 12 ou 24V

Heatbed 200 x 300mm x 3mm MK3

-Épaisseur 3mm 

-En aluminum 

Heatbed 300 x 300 x 2 mm MK2a

-Épaisseur 3mm 

-En aluminum 

Heatbed 200x 200 x 2mm MK2B

8.4x8.4 inch RepRap mendel PCB

- 2 mm épaisseur

-Dual power 12 / 24V

Heatbed 200 x 300 x 2mm MK2a

Size: 300*200 x 2mm 
Power Input: 12V 
Copper plated holes
Resistance between 1.2 and 1.5 ohm
Maximum temperature: 100C

Heatbed sticker adhesive plate

Heat bed 200 x 200mm: (prix: 9,75$

Heat bet 200 x 300mm : (prix: 14,40$)

Heat bed 300 x 300mm  (prix: 18,50$)